At RKM Homes we treat solar and battery readiness as part of the electrical and structural design rather than an afterthought. Pre-wiring while framing and finishing saves time and money compared with retrofits: you can plan conduit runs, roof penetrations, service capacity and a dedicated inverter/battery location before finishes are installed, avoid chasing cables through finished walls, and size the main service and subpanels to accommodate future PV arrays, inverters and a backup load center. In Denver that also means accounting for roof pitch, snow-shedding, and southern exposure when locating the array and the conduit chase so installers have straightforward access and minimal rooftop penetrations.
Practically, the steps we follow on every project include coordinating early with a licensed electrician and a prospective solar/battery installer, performing a whole-house load analysis, and reserving space in the main electrical service for the inverter and transfer or disconnect equipment. We run one or more dedicated, oversized conduits from the planned roof array location down to the mechanical/electrical room (one conduit for PV conductors, another for communications and monitoring lines), install a roof-mounted junction box or accessible rooftop combiner location and block the roof decking for racking. We specify an inverter location near the main panel to minimize cable runs, allow required clearances and ventilation for batteries, and leave room in the main panel or a labeled subpanel for the inverter output breaker and automatic transfer switch or critical-load panel for whole-home or partial backup.
Code, permits and utility interconnection rules will determine some details, so we document PV-ready features on the plans: main service capacity and spare breaker spaces, a labeled pathway from roof to service, a dedicated battery cabinet location with required clearances and ventilation, and space for an AC disconnect at the meter. We also future-proof the home for EV charging and potential system upsizing by oversizing conduit and leaving access panels where needed. If you’re building on your lot, we’ll incorporate these items into the construction schedule and drawings so your home is ready for a streamlined solar + storage installation when you’re ready to move forward.
How do I determine which circuits are critical and how much solar and battery capacity my new home will need?
Start by gathering 12 months of utility bills and making a room-by-room inventory of all major loads with their running and startup wattages (manufacturers’ nameplate or typical ranges are fine). Separate everything into “everyday/whole-house” versus “critical/backup” groups — critical loads are what you want to run during an outage (refrigerator, freezer, selected lights, internet/router, sump/well pump, one heating zone or medical equipment, garage door, etc.). For each item list running watts, estimated hours of use per day, and whether it has a high inrush/startup draw (fridges, pumps and AC compressors commonly do). As a builder, we make that prioritized critical-load list part of the electrical plan so the electrician and solar designer can size a dedicated critical-load subpanel and label circuits now rather than trying to retrofit later.
To size batteries, convert your prioritized critical loads to daily kilowatt‑hours: add (running watts × hours per day)/1,000 for each appliance to get total critical kWh/day. Decide how many days of autonomy you want (common choices: overnight-only, one full day, or multiple days) and account for usable battery capacity and round‑trip efficiency. Use this working formula: required battery bank (kWh) = (critical kWh/day × days of autonomy) / (usable capacity fraction × round‑trip efficiency). For example, if critical loads total 3 kW continuously (≈72 kWh/day) and you plan for one day of backup using batteries with about 80% usable capacity and ~90% round‑trip efficiency, you’d specify roughly 72 / (0.8 × 0.9) ≈ 100 kWh of battery capacity.
When you size the solar array, include the home’s annual or daily energy use plus any planned EV charging or growth. Estimate expected local production (Denver projects typically see roughly 4–5 kWh per installed kW per day, depending on roof orientation and shading) and divide your daily kWh need by that production number to get a starting array kW. Example: a house using 30 kWh/day plus a planned EV adding 9 kWh/day equals 39 kWh/day; at 4.5 kWh/kW/day you’d start with ~8.7 kW of panels and then add 10–20% headroom for future EV use or lifestyle growth. Deliver your load worksheet, autonomy target, and EV projections to your solar designer and electrician early so circuits, conduit capacity, and space for future inverters/batteries can be planned during framing and rough‑in.
What service capacity, main panel/subpanel layout, meter location and service‑entrance upgrades should I plan for when pre‑wiring a new home for solar and battery storage?
Start by sizing the service for more than your immediate needs. A 200‑amp service is still common for new homes, but if you plan on whole‑home battery backup, fast EV chargers, or future load growth, consider upgrading to 320–400 amps or specifying a 200‑amp main with provisions for an easy service upgrade. As the builder I ask homeowners to decide early whether they want whole‑house backup or only critical‑loads support: whole‑house backup often requires the inverter and transfer equipment to interface with the main service at higher currents, so provide space and labeling in the main service equipment for a future 100–200A inverter feed (exact size comes from the inverter spec). Don’t let your electrician guess — reserve dedicated breaker space and bus capacity equivalent to the expected inverter/interconnection breaker so you won’t need a full panel replacement later.
Where you put the main panel, subpanel(s) and meter makes installation and future maintenance much simpler. Locate the main service and the anticipated inverter/battery location as close as practical so AC conductors are short; place a dedicated “critical‑loads” subpanel adjacent to the battery/inverter location so transfer switches only need short runs to the loads you want backed up (fridge, HVAC, well pump, etc.). When planning the meter placement, favor an exterior wall with direct utility access and room for a potential meter/socket upgrade or CT (current‑transformer) ring if the utility requires bidirectional metering or export controls. Tell your builder and electrician where you want the inverter and battery early so panels and subpanels can be oriented and knocked out for future feeders, and leave at least 20–30% of breaker space open in the main and critical subpanel for future solar/battery circuits.
Practical next steps to include in your build specifications: require the electrical contractor to document reserved breaker positions (labelled “PV/INV” and “BATTERY”), sized conduit stub‑outs from the main panel location to the future inverter/battery wall, and a dedicated route for the utility service upgrade if needed. Coordinate with the local utility during the design phase — service‑entrance upgrades (transformer or line capacity changes, meter relocation) can add lead time and costs, so get a preliminary utility feasibility check before framing. Finally, insist on the clear working space and mechanical mounting provisions around panels and the meter per code so inspectors and utility crews can access equipment without rework.
How should conduit routes, wiring pathways and roof penetrations be planned for a solar array on my new custom home?
From the builder’s side I treat array placement and roof penetrations as part of the roof framing plan, not an afterthought. Identify the preferred roof slopes and racking layout early so penetrations fall over rafters or engineered truss bays where I can add blocking or beef up sheathing. South‑facing, unshaded slopes are ideal, but if you need multiple exposures plan the attachment rows and penetrations to avoid valleys, flashings, chimneys and dormers. Decide up front whether you want penetrating mounts or ballasted/rail systems for your roof type — penetrating mounts need reinforced points and integrated flashing details that we install during framing.
Plan conduit routes to keep DC and AC runs short and accessible. I recommend leaving a dedicated, continuous raceway from the array down to the inverter/battery area — for future flexibility we typically put a 1.5–2″ conduit stub from the roof to the mechanical or garage wall for PV strings, and a separate 1″ conduit from the inverter location to the main service/subpanel for AC output. Always pull a labeled pull‑string and leave generous service loops in the attic or behind the inverter so the solar installer won’t need to redo drywall. Keep AC and DC conduits separate and routed to an accessible service wall or mechanical room to simplify the location of combiner boxes, disconnects and future expansions.
Ask your builder for very concrete items on the plans: show exactly where the roof penetrations will be, install blocking at each planned attachment point, route the conduit chase inside the wall cavity or through a protected chase, and provide a weather‑tight roof curb or consolidated penetration area where practical to reduce the number of roof holes. Install removable attic/closet access and a labeled junction box or conduit knockout plate on the interior wall where the inverter/battery will sit so the solar crew can tie in cleanly. Finally, require that racking attachment points be verified by a structural engineer for local snow/wind loads — that prevents costly retrofits later.
Where should I place my home battery and what ventilation, fire‑code clearances, disconnects and automatic transfer/safety systems do I need?
As a custom home builder I treat battery siting like any other mechanical appliance: accessible, serviceable, and close to the inverter or main electrical distribution to minimize high‑current cable runs. Good locations are a conditioned utility room, an attached garage on a non‑living wall, a dedicated mechanical closet on the ground floor, or an exterior weather‑rated cabinet mounted on a foundation wall. Avoid placing battery packs inside bedrooms, over finished living spaces without structural reinforcement, or where they will be exposed to direct sun and heat; if you plan a second‑floor install, budget for floor reinforcement and a service hatch or clear route for replacement. When we lay out the plans we locate a 2″ minimum chase from the battery location to the inverter and main panel and a separate 1″ conduit for BMS/monitoring cables so future upgrades don’t require tearing open drywall.
Ventilation and fire‑safety clearances depend on battery chemistry and local enforcement, but you can pre‑wire for either scenario to keep options open. For vented lead‑acid systems plan for an exhaust path to exterior (passive louvers or a small dedicated fan) because hydrogen can accumulate at the ceiling; for lithium‑ion packs provide thermal management space, temperature sensors, and at least the same clear working area required for electrical equipment — we design a 30″‑wide by 36″‑deep clear service zone in front of the battery inverter/equipment. Leave a 12–24″ buffer from combustibles and any HVAC return grills, and reserve room for a listed battery enclosure or fire‑rated barrier if your local authority requires it. We also prewire a power circuit for an exhaust fan or for an enclosure heater/cooler if needed, and install temperature and smoke detection wiring back to the home control panel.
Make safety and shutoffs intuitive for installers and emergency personnel by pre‑planning disconnects and transfer gear. Specify and prewire space for a visible, labeled AC disconnect at the exterior or utility area, a local DC disconnect adjacent to the battery, and an accessible emergency disconnect within sight of the equipment; run short, straight conduit routes so those disconnects can be added without reworking walls. If you want backup power, we prewire a location for an automatic transfer switch or an inverter/transfer assembly next to the main panel and pull control conductors (thermostat‑type or higher‑level communications) so the ATS, generator or future whole‑house backup can be integrated neatly. Finally, insist on battery management system (BMS) wiring, temperature cutoff interlocks and clear labeling for all conductors so maintenance and any future expansion are straightforward and meet first‑responder expectations.
What permitting, utility interconnection/net‑metering rules and inverter architecture (AC vs DC coupling) do I need to consider when pre-wiring my new home for solar and batteries?
Start the permit and interconnection conversation before framing and rough‑in. As your builder we request the utility’s residential interconnection packet and any local AHJ (building department) requirements up front so the electrician can include the correct disconnects, labeling, meter location and equipment clearances in the plans submitted for permit. Utilities commonly require a bi‑directional or revenue‑grade meter location and a visible utility disconnect near the meter; some jurisdictions also require the inverter and battery to be shown on the electrical permit with manufacturer specs and voltage/current ratings. Bring those utility and permit documents to your design meeting and ask us (and your electrician) to show the inverter and main breaker locations on the electrical plan so the inspector and the utility can approve the layout without rework.
Choose an inverter architecture now or pre-wire to accommodate either AC‑ or DC‑coupled systems so you don’t box yourself into an expensive retrofit. AC‑coupled systems (inverter + separate battery inverter/charger) simply require a dedicated 240V circuit and space in the electrical room or garage for the inverter(s) and a clear breaker position in the main or subpanel; DC‑coupled systems require shorter DC runs from the array to the battery/inverter and a DC‑rated combiner/route from the roof to the equipment. If you’re unsure which you’ll pick later, we recommend installing multiple conduits from the roof to the planned equipment wall (one sized and rated for PV string conductors and one reserved for future battery or inverter DC/AC cabling) and reserving extra breaker spaces in the panel so either architecture can be connected without tearing sheetrock.
Practical, on‑site steps we do for every custom home to make permitting and interconnection painless: locate an accessible exterior meter wall and reserve 4–6 ft of clear wall space next to it for the inverter/utility disconnect; run at least two dedicated conduits from the roof penetration location to that inverter wall (separate conduit for PV strings and for future battery cabling or communications); and leave 2–3 empty 1‑inch or larger conduits with pull strings for future communications or monitoring wiring. Coordinate with the solar contractor’s one‑line wiring diagram during rough‑in so the AHJ sees exact locations and so the final inspector and utility field crew can make the connection quickly — that saves weeks on interconnection approvals and avoids rework after drywall.

