As a Denver-based custom home builder that designs and constructs homes on your lot, we at RKM Homes start every project by separating what actually holds the house up from what makes it look and function the way you want. That distinction matters whether you’re planning a full custom build, a kitchen reconfiguration, or a small remodel: structural elements determine the layout limits, permitting and engineering needs, construction cost, and long-term performance under local conditions like Denver-area snow loads and variable soils. Knowing which parts of a house are structural helps you make confident decisions about where you can create openness, add windows, or alter room locations — and where you’ll need a licensed engineer and temporary shoring.
Structural elements are the components that carry and transfer loads to the ground and resist lateral forces. Typical examples include the foundation system (concrete slab-on-grade, crawlspace, or full basement with footings), load-bearing walls, primary beams and girders (steel sections, LVLs, or glulam timbers), columns and posts, floor joists and subfloor assemblies, roof framing (rafters, trusses, ridge beams) and shear walls or diaphragms that stabilize the structure against wind and seismic forces. Stair framing and chimney foundations are also structural. Altering any of these requires structural calculations, permits, and usually temporary supports; headers over window and door openings are structural components that must be sized properly when enlarging or relocating openings.
Non-structural elements are those you can generally change without affecting the building’s ability to carry loads, though many still require coordination with trades and occasionally permits. Examples include interior partition walls that are non-load-bearing, cabinetry and built-ins, trim, drywall and paint, countertops, flooring finishes, light fixtures, sinks and most HVAC ductwork and mechanical equipment mounting (the equipment itself is non-structural, but its supports and penetrations must be detailed). Windows and exterior cladding are typically non-structural elements, but creating new openings or changing window sizes involves headers or framing that are structural. When you work with us, we identify these distinctions early so you understand which ideas are straightforward and which will trigger engineering, permitting and additional budget or schedule considerations.
How can I tell which walls and other elements in my house are load-bearing versus non-load-bearing?
Load-bearing elements carry weight from the roof and upper floors down to the foundation; non-load-bearing (or partition) elements only support their own weight or separate spaces. As a builder, I look first at the load path: exterior walls are almost always bearing, and interior walls that run perpendicular to floor joists or line up directly over beams, posts or foundation walls below are typically load-bearing. Continuous walls that stack from the foundation through multiple floors are almost always carrying load, as are walls with large solid headers above openings—those headers exist to transfer roof or floor loads around a doorway or opening.
You can do several practical checks yourself before calling a pro. Go to the basement or crawlspace and look for beams, columns or foundation walls directly under the wall in question; if you find a beam pocket or post beneath it, that wall is bearing. In the attic or top floor, check joist and rafter directions—walls perpendicular to joists are likely bearing, while walls parallel to joists are often partitions. Look for structural clues inside walls where accessible: a double top plate, a heavy header over a doorway, thicker wall construction or masonry (brick/block) almost always indicate a structural role. Take photos from the attic and basement and note joist directions to show your contractor.
If you plan to remove or alter a wall, treat it as potentially structural until a structural engineer or experienced contractor confirms otherwise. Temporary shoring is often required when you open a wall, and many remodels use a properly sized beam (LVL or steel) and bearing posts to relocate loads so you can create an open plan. Also remember non-structural walls often contain plumbing, HVAC or electrical runs—so even if a stud wall isn’t supporting weight, it may still need careful handling and permits.
How do foundation, footings, and soil conditions affect my home’s structural integrity and renovation options?
As a custom home builder working across the Denver metro, I treat the foundation, footings and underlying soil as the single most important structural system of a house. Footings transfer the weight of load-bearing walls, beams and columns into the soil; the foundation (basement wall, crawlspace wall or slab) carries those loads up to the structure. The soil’s bearing capacity and behavior — common local issues are expansive clay, variable fill, and seasonal moisture swings — dictate footing size, depth and whether we need engineered solutions like piers or reinforced slabs. For any renovation that removes or alters walls you must verify what the footings and foundation were designed to carry, because you can’t safely shift loads without redesigning the foundation support.
Homeowners can and should do a few practical checks before calling a builder or engineer. Look for stepped or horizontal foundation cracks, doors and windows that stick, uneven or sloping floors, and visible offsets at the foundation line — those are red flags. Hairline vertical cracks are often cosmetic; cracks wider than about 1/4 inch or any horizontal displacement warrant a structural engineer’s assessment. Before buying or starting an addition, request the geotechnical/soil report and foundation plans if they exist; if you don’t have one, budget for a soil study and compaction tests because they determine accepted bearing values and required footing sizes.
There are actionable steps homeowners can take to protect the foundation and keep renovation costs down. Maintain positive drainage away from the house (a common rule I use on-site is a 6-inch drop in the first 10 feet), keep downspouts extended several feet from the foundation, avoid large trees close to the foundation, and use controlled irrigation to prevent extreme wet/dry cycles. For problem soils or heavy remodels, plan for engineered footing designs — helical piers, drilled piers or underpinnings — and insist on compaction and footing inspections during construction. Early engagement of a geotechnical consultant and structural engineer saves money and prevents surprises once the framing starts.
What are the structural differences between roof, floor, and wall systems in a custom home?
As a custom home builder I look at the roof as a primary load-bearing system that moves dead loads (roofing, sheathing) and live loads (snow, maintenance workers) down to the exterior and interior supports. Key structural members you’ll see are rafters or prefabricated trusses, ridge beams or bearing walls, collar ties/ceiling joists and the roof sheathing (OSB or plywood). In Denver and other snowy climates we size members and specify truss or rafter spacing to handle snow loads; choosing trusses for a new home can give predictable spans and lower attic framing costs, but it limits future attic remodeling because truss webs can’t be chopped up. For homeowners planning changes, note that roof ventilation, insulation and shingles are non-structural layers that affect performance but don’t carry load — altering framing requires engineered solutions, not just swapping coverings.
Floor systems are where homeowners most often notice structural issues: squeaks, bounce, and sag in a room are signs the joists, beams or subfloor are not performing as expected. Typical structural elements are floor joists (dimensional lumber or engineered I-joists), girders or LVL/glulam beams, and the structural subfloor (tongue-and-groove OSB or plywood). The finished flooring (hardwood, tile, carpet) is non-structural but depends on a stiff, properly supported subfloor; heavy installations (stone tile, claw-foot tub, hot tub) may require upgraded joists or added beams. If you’re remodeling, don’t cut or notch joists without confirmation — small changes can reduce capacity; common remedies we use are sistering joists, installing a new beam with proper bearings, or adding posts to transfer loads to the foundation.
Exterior and interior walls play different structural roles: exterior walls usually carry roof and floor loads down to the foundation and act as part of the lateral-resistance system when sheathed with plywood or OSB, while many interior partitions are non-load-bearing and can be moved without replacing the primary structure. Signs a wall is load-bearing include its alignment with beams or walls directly above/below, a continuous bearing path down to the foundation, or heavy headers over openings; if you can find a beam in the basement or a wall directly under a roof ridge, that’s a clue. For any planned removal or large opening, we always temporary-shore and install an engineered header (LVL or steel) sized for the span — trying to guess capacity from appearance risks structural damage and costly fixes, so engage your builder or structural engineer before demo.
Are mechanical, electrical, plumbing, and interior components considered non-structural, and what should I know before remodeling them?
Mechanical, electrical and plumbing (MEP) systems and interior finishes—things like ductwork, branch wiring, water supply and drain lines, cabinets, interior doors, trim and non-load-bearing partition walls—are typically non-structural: removing or altering them won’t normally compromise the building’s stability. That said, “non-structural” doesn’t mean trivial. Plumbing stacks often run through wall cavities that also contain headers or bearing elements, heavy fixtures (cast-iron tubs, large stone countertops, water heaters) impose concentrated loads, and large duct chases can interact with floor and ceiling framing. From a builder’s standpoint, we treat MEP and interior items as service systems that must be planned so they don’t inadvertently conflict with structure, insulation, firestopping or access requirements.
If you’re planning a remodel, practical steps matter: turn off and label circuits at the panel before demo, locate main water shutoffs and isolation valves, and identify the soil stack and main drain lines before moving bathrooms or kitchens. Expect electrical changes to trigger load calculations—dedicated circuits for ovens, HVAC compressors, or an EV charger may require a panel upgrade or new feeder work. When moving plumbing fixtures, check for required trap/vent locations and slope for drain lines; moving a tub or stack can mean cutting and re-routing joists or installing new headers, which becomes structural work and needs an engineer and permits. For HVAC, plan register locations and duct runs early so soffits and ceiling drops are integrated into the design rather than retrofitted.
On custom projects we always coordinate trades early to avoid costly rework: we mark out plumbing stacks and panel locations on framing prints, provide clear service access (the NEC requires working space in front of electrical panels—plan that clearance), add access panels for valves and cleanouts, and specify vibration isolation pads or blocking where heavy equipment sits. Budget a contingency for rerouting hidden services and for permit/inspection time—what looks like a simple cabinet or fixture relocation can cascade into framing or routing changes. If you’re unsure whether a wall is load-bearing or whether a fixture will need additional support, call a builder or structural engineer before demo: that front-end check saves money and time on every remodel.
What building codes, inspections, structural assessments and renovation constraints affect my custom home?
As a Denver custom home builder I tell clients that the moment a change alters how loads are transferred through the house—or when you change the footprint, add square footage, or open up walls—you’re moving into work that will trigger permits and structural review. Practically, that means anything like enlarging window or door openings, removing or relocating walls, adding a second floor or dormer, or modifying roof framing will require stamped drawings from a structural engineer and plan approval from the local building department before work starts. Even if the change feels “cosmetic,” if it requires cutting into framing or adding support you should assume an engineer’s input and a permit are required.
Inspections are scheduled events you should track closely. Typical milestones are plan review/permit issuance, footing/foundation inspection (if applicable), rough framing inspection, rough MEP (mechanical, electrical, plumbing) inspections, insulation/air barrier, and final inspection/sign-off. As your builder I make sure stamped structural calculations and approved plans are on the jobsite and that the inspector’s card is posted; as a homeowner, ask to see those documents and the inspection schedule before work begins. Small non-structural projects—like replacing finishes, cabinets, or trim—often don’t need a structural permit, but electrical and plumbing changes usually do, so confirm with your contractor which trades require inspections.
Renovation constraints go beyond engineering: zoning limits, setback rules, historical-district restrictions, easements, HOA approvals, and utility locations can all shape what structural changes are feasible and how much engineering is required. Hidden conditions—rot, insect damage, undersized existing members, or unpermitted previous work—frequently increase scope, cost, and the need for remedial structural work, so build a contingency into your budget and timetable. My practical advice: require a pre-construction structural assessment, get stamped drawings and permit approvals in writing, hire licensed contractors who carry the right insurance, and withhold final payment until inspections are passed and you have formal sign-off—this protects your investment and resale value.

